News & Updates

News

8.12.23 4Ming Boost: High drawn parts on mechanical presses
2.12.23 Average roughness conversion
November 29, 2023 Roughness & process selection
10/28/2023 Penetration Multiple drawing
9/24/2023 Multiple bending
9/2/2023 Spring back compensation
August 23, 2023 The 4Ming press: Innovation in deep drawing of sheet metal
Aug 4, 2023 4Ming Press Data Sheet
8/1/2023 English version 4Ming manual
July 16, 2023 4Ming Press Productivity
July 15, 2023 4Ming press for beer barrels in comparison
July 3, 2023 4Ming Press
June 10, 2023 Deep drawing & ironing
June 4, 2023 Investment comparison
June 2, 2023 Economical lot size
May 20, 2023 Multiple drawing, process flow
May 9, 2023 Stamp printing & stamp compression , additions
May 9, 2023 Entry angle , additions
May 8, 2023 Friction values & pulling result
April 25, 2023 Yield stress according to Ludwik
April 21, 2023 Glossary
March 25, 2023 Singularity
March 23, 2023 Construction of the drawing press
March 23, 2012 Drawing press for tank fitting
March 19, 2023 4Ming - Service description
3/18/2023 Overall safety factor
March 18, 2023 Plastic support number
March 18, 2023 Static component strength
March 18, 2023 Proof of strength of sheet metal structures
March 16, 2023 Simulation embossing
3/16/2023 Rectangular hollow embossing
March 14, 2023 Design guidelines for hollow embossing
January 22, 2023 Embossing, additions
12/22/2022 Stretch forming capability
December 16, 2022 Internal high-pressure forming of drawn parts
12/4/2022 AlMgSi flow curve
11/10/2022 Flow curve Al 99.5
November 6, 2022 Deep drawing & injection molding
October 30, 2022 Warm forming stainless steel
July 22, 2022 Material behavior
July 21, 2022 young's modulus & temperature , young's modulus & elongation
July 20, 2022 young's modulus
June 23, 2022 Collar setting
June 12, 2022 Reshape & Calibrate
May 29, 2022 Maximum embossing height for embossing
May 28, 2022 Embossing
May 27, 2022 Anisotropy table
May 25, 2022 Anisotropy , updates
May 22, 2022 Embossing power embossing
May 19, 2022 Ironing
May 12, 2022 Maximum force for die stamping
May 10, 2022 Friction & Tribology
May 7, 2022 V-Die Bending, Updates
May 4, 2022 Cutting length & bending shortening
April 18, 2022 Spring back
April 9, 2022 Hat profile bending
March 6, 2022 Free bending
March 1, 2022 Bending & die bending
February 11, 2022 Optimize deformation
2/3/2022 Forming-Analysis
December 30, 2021 Natural strain & equivalent natural strain
May 31, 2021 Anisotropy
May 15, 2021 Yield strain
March 8, 2021 Moments of area ring
February 20, 2021 Article about cutting completed

Updates

Feb 19, 2022 Screw selection
2/3/2022 Stripper force
March 8, 2021 bend
March 8, 2021 Bending cutting punch Normal conditions
March 8, 2021 Bending cutting punch Unfavorable conditions
February 20, 2021 Preface, miscellaneous